Showing posts with label Ooshies. Show all posts
Showing posts with label Ooshies. Show all posts

Monday, August 31, 2026

Completed Project: Ooshie Stand

 

Those of you who are regular visitors to this blog while have been following the progress of the five tier 'Ooshie Stand'.   This has been sourced from Thingiverse.   To hold the entire run of the designs each level consists of eight holding spots - five levels allowed the entire run of forty designs to be displayed.

The decision has been made to spray paint the entire design in a single colour (which is purple as shown left).   The design was completed as noted in stages and each section was able to be screwed into the section above it.

This allowed the design to be put together successfully for a price point of under $10.00.   It also has the bonus of allowing the forty different characters to be transported without them falling off the design as each is held in place by an individual peg.

This is another example of using a pre-made design or feature and creating a interest and design for discussion and sharing with adults and also students.

Sunday, August 9, 2026

Ooshie Stand: Personalised Example

 

Challenge: To produce a personalised stand for Ooshies or Lego Mini Figures.

Background: This is the follow up from yesterdays post with the generation of ideas follow up.   We are continuing to explore further developments and ideas but to encourage the students with their designs we wanted to print a physical example that could then be used to review the ideas and consider what refinements might be required or considered.   As noted in the post yesterday this was intended for one of two things as a personalised display stand - the scale of which in theory would allow a range of the figures to be displayed.

The figures in the range were measured prior to the construction of the stand - however there is a subtle variation in the size of a lot of the figures and some have arms and other features that stick out from the base meaning that a universal stand needs to take thins into account.  In this example here the student made a slight design error that the last bay, the one with the second star is not the same dimensions of the other three and finding a character to fit in it is going to be one of the issues that the students will need to resolve.  In the example that was used with the run of twenty figures a peg has been introduced for each figure to be held in place.  In this student example the student opted to have a small division between the figures with the name of the person and the stars on either side.

This was done by applying simple fonts and also including the two 'stars' either side to ensure that there was balance and not blank sections of the design.

Finally we are always looking at considerations towards rafting or waste of plastic - there was the underneath of the design here.  A much better option for the student would have been to print the feet of the stand separately so they could glue them to the base post printing so that there would be no need for support - which essentially was nearly half the print.

Resources used to complete this print: Tinkercad App, student iPad, Bambu H2D, Blue PLA.

Level of Difficulty: Medium all of the skills that the student needed to complete the print they possessed and one would anticipate with the refinements and adjustments that they are going to make the print will be successful.

Size: The print currently measures 170mm long is 35mm wide and is currently on four feet that are 10mm high each.   The sections of the print are currently 35mm by 35mm - this will need to be revised, except for the last bay which is 25mm by 35mm and is too small for anything except for the smallest of the Ooshies.

Cost/Price: This print as it stands now uses 35g of PLA to complete the print which has a price point currently of $0.75.   As noted this could be reduced significantly by altering the underside of the print and printing the legs as seperate pieces as the weight of the objects being placed on them is minimal.

Timeframe: Two hours and ten minutes to complete (again as stated if we changed the base it would also halve the total print time.

What we would do differently/Next steps for the students - these have been more or less addressed in the additional information in the print which would affect the output.

Friday, August 7, 2026

Ooshie Stand: Generating Ideas

 

One of the areas of excitement at the moment is a group of collectible toys that are available from a local supermarket.   They are collectables aimed at 'encouraging' the purchase at the franchise which then gifts the buyer a range of the toys.  They range in height from 30-40mm and generally 30mm wide.

In this example shown left one of the teachers from our school used Chat GPT to create a model stand for their classroom collection.   The stand was connected via interlocking pieces (and is not glued together).   In this instance the print was completed using glow-in-the-dark filament. 

This inspired our classroom to consider how they might be able to create and design their own version of these and consider how they might be personalised or developed further.   The size of the objects that need to be displayed meant that a small print would be completed for the project.

As we do typically with this kind of design project the first stage is for the students to build a virtual design and then test its viability by using the Tinkercad App to project an image of their own versions into different locations around the school to look at its presentation, scope and scale.  

In this example shown left the student has advanced the teachers design by adding a name on the top of the highest shelf.   The students were then able to share the designs back to each other to consider how they could develop, expand and then further adapt their designs.    Once this has been completed the process of printing out several of the designs will be completed to again use as examples and review them, consider them and help guide and refine their designs.